various updates
This commit is contained in:
morrownr
parent
46e2665214
commit
bcfd5dcc9f
@ -68,11 +68,11 @@ options 88x2bu rtw_drv_log_level=0 rtw_led_ctrl=1 rtw_vht_enable=1 rtw_switch_us
|
||||
#
|
||||
# Beamforming options ( rtw_beamform_cap )
|
||||
#
|
||||
# 0 = Disable (default)
|
||||
# 0 = Disable
|
||||
# 1 = SU Beamformer
|
||||
# 2 = SU Beamformee
|
||||
# 3 = SU Beamformer and SU Beamformee
|
||||
# 10= SU Beamformee and MU Beamformee
|
||||
# 10= SU Beamformee and MU Beamformee (default)
|
||||
# 11= SU Beamformer and SU Beamformee and MU Beamformee
|
||||
#
|
||||
# Note: MU Beamformer is not supported.
|
||||
|
||||
5
Makefile
5
Makefile
@ -75,7 +75,6 @@ CONFIG_GSPI_HCI = n
|
||||
CONFIG_AP_MODE = y
|
||||
CONFIG_P2P = y
|
||||
CONFIG_MP_INCLUDED = n
|
||||
CONFIG_CONCURRENT_MODE = n
|
||||
CONFIG_POWER_SAVING = y
|
||||
CONFIG_IPS_MODE = default
|
||||
CONFIG_LPS_MODE = default
|
||||
@ -83,7 +82,7 @@ CONFIG_USB_AUTOSUSPEND = n
|
||||
CONFIG_HW_PWRP_DETECTION = n
|
||||
CONFIG_BT_COEXIST = y
|
||||
CONFIG_WAPI_SUPPORT = n
|
||||
CONFIG_EFUSE_CONFIG_FILE = y
|
||||
CONFIG_EFUSE_CONFIG_FILE = n
|
||||
CONFIG_EXT_CLK = n
|
||||
CONFIG_TRAFFIC_PROTECT = n
|
||||
CONFIG_LOAD_PHY_PARA_FROM_FILE = y
|
||||
@ -99,7 +98,7 @@ CONFIG_SIGNAL_SCALE_MAPPING = n
|
||||
CONFIG_80211W = y
|
||||
CONFIG_REDUCE_TX_CPU_LOADING = n
|
||||
CONFIG_BR_EXT = y
|
||||
CONFIG_TDLS = n
|
||||
CONFIG_TDLS = y
|
||||
CONFIG_WIFI_MONITOR = y
|
||||
CONFIG_MCC_MODE = n
|
||||
CONFIG_APPEND_VENDOR_IE_ENABLE = n
|
||||
|
||||
16
README.md
16
README.md
@ -48,7 +48,7 @@ confirm that this is the correct driver for your adapter.
|
||||
### Compatible Kernels
|
||||
|
||||
- Kernels: 4.19 - 5.11 (Realtek)
|
||||
- Kernels: 5.12 - 6.1 (community support)
|
||||
- Kernels: 5.12 - 6.2 (community support)
|
||||
|
||||
### Tested Compilers
|
||||
|
||||
@ -81,7 +81,7 @@ be provided via PR or message in Issues.
|
||||
|
||||
- SkiffOS for Odroid XU4 (ARM 32 bit) (kernel 6.0.7)
|
||||
|
||||
- Ubuntu 22.04 (kernel 5.15) and 22.10 (kernel 5.19)
|
||||
- Ubuntu 22.04 (kernel 5.15) and 22.10 (kernel 5.19) (kernel 6.2 rc1)
|
||||
|
||||
- Void Linux (kernel 5.18)
|
||||
|
||||
@ -90,10 +90,10 @@ supported due to the way kernel patches are handled. I will support
|
||||
knowledgable RHEL developers if they want to merge the required
|
||||
support and keep it current.
|
||||
|
||||
Note: Android is not supported but I will support knowledgable Android
|
||||
developers if they want to merge and keep current the required support
|
||||
(most likely just instructions about how to compile and maybe a modification
|
||||
or two to the Makefile).
|
||||
Note: Android is supported in the driver according to Realtek. I will support
|
||||
knowledgable Android developers if they want to merge and keep current the
|
||||
required support (most likely just instructions about how to compile and maybe
|
||||
a modification or two to the Makefile).
|
||||
|
||||
|
||||
### Download Locations for Tested Linux Distributions
|
||||
@ -120,7 +120,7 @@ or two to the Makefile).
|
||||
|
||||
### Compatible Devices
|
||||
|
||||
Warning: If you are looking for information about what adapter to buy,
|
||||
Note: If you are looking for information about what adapter to buy,
|
||||
click [here](https://github.com/morrownr/USB-WiFi) and look for Main Menu
|
||||
item 2 which will show information about and links to recommended adapters.
|
||||
|
||||
@ -217,7 +217,7 @@ If it is not set, you will likely have problems accessing some channels, especia
|
||||
5 Ghz and 6 GHz channels. To set your Country Code:
|
||||
|
||||
```
|
||||
iw reg set US
|
||||
sudo iw reg set US
|
||||
```
|
||||
|
||||
If you are not in the US, please use the country code for your country. See:
|
||||
|
||||
File diff suppressed because it is too large
Load Diff
@ -1,4 +1,4 @@
|
||||
2022-11-15
|
||||
2022-12-27
|
||||
|
||||
What is Concurrent Mode?
|
||||
|
||||
@ -10,7 +10,7 @@ single WiFi adapter.
|
||||
|
||||
For example:
|
||||
|
||||
Use station mode (called managed or client mode also) to connect with an
|
||||
Use station mode (also called managed or client mode) to connect with an
|
||||
AP to access the internet at the same time as it also performs as an AP
|
||||
to allow other devices to connect to the second interface.
|
||||
|
||||
@ -35,13 +35,13 @@ nano Makefile
|
||||
Change the following line:
|
||||
|
||||
```
|
||||
CONFIG_CONCURRENT_MODE = n
|
||||
#EXTRA_CFLAGS += -DCONFIG_CONCURRENT_MODE
|
||||
```
|
||||
|
||||
to
|
||||
|
||||
```
|
||||
CONFIG_CONCURRENT_MODE = y
|
||||
EXTRA_CFLAGS += -DCONFIG_CONCURRENT_MODE
|
||||
```
|
||||
|
||||
and then install the driver per the installation steps. If
|
||||
@ -50,10 +50,15 @@ the driver is already installed, run the following first:
|
||||
```
|
||||
sudo ./remove-driver.sh
|
||||
```
|
||||
and then reinstall the driver with:
|
||||
|
||||
```
|
||||
sudo ./install-driver.sh
|
||||
```
|
||||
|
||||
Once the driver is fully installed and you have rebooted the system, you
|
||||
can verify that this works by typing the “iw dev” command, You should
|
||||
see two wireless interfaces, and the MAC address of secondary interface
|
||||
can verify that this works by typing the “iw dev” command. You should
|
||||
see two wireless interfaces, and the MAC address of the secondary interface
|
||||
is nearly the same as the first except for one digit.
|
||||
|
||||
-----
|
||||
|
||||
@ -42,7 +42,8 @@
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_80211AC_VHT
|
||||
#define CONFIG_BEAMFORMING
|
||||
/* nrm - activates beamforming */
|
||||
/* #define CONFIG_BEAMFORMING */
|
||||
#endif
|
||||
|
||||
/* set CONFIG_IOCTL_CFG80211 from Makefile */
|
||||
|
||||
File diff suppressed because it is too large
Load Diff
@ -16,7 +16,7 @@
|
||||
# GNU General Public License for more details.
|
||||
|
||||
SCRIPT_NAME="remove-driver.sh"
|
||||
SCRIPT_VERSION="20221218"
|
||||
SCRIPT_VERSION="20221228"
|
||||
MODULE_NAME="88x2bu"
|
||||
DRV_VERSION="5.13.1"
|
||||
|
||||
@ -57,23 +57,44 @@ do
|
||||
done
|
||||
|
||||
# displays script name and version
|
||||
echo "Running ${SCRIPT_NAME} version ${SCRIPT_VERSION}"
|
||||
echo "Script: ${SCRIPT_NAME} version ${SCRIPT_VERSION}"
|
||||
|
||||
# check for and remove non-dkms installation
|
||||
# check for and remove non-dkms installations
|
||||
# standard naming
|
||||
if [[ -f "${MODDESTDIR}${MODULE_NAME}.ko" ]]
|
||||
then
|
||||
echo "Removing a non-dkms installation."
|
||||
echo "Removing a non-dkms installation: ${MODDESTDIR}${MODULE_NAME}.ko"
|
||||
rm -f ${MODDESTDIR}${MODULE_NAME}.ko
|
||||
/sbin/depmod -a ${KVER}
|
||||
fi
|
||||
|
||||
# check for and remove non-dkms installations
|
||||
# with rtl added to module name (PClinuxOS)
|
||||
if [[ -f "${MODDESTDIR}rtl${MODULE_NAME}.ko" ]]
|
||||
then
|
||||
echo "Removing a non-dkms installation: ${MODDESTDIR}rtl${MODULE_NAME}.ko"
|
||||
rm -f ${MODDESTDIR}rtl${MODULE_NAME}.ko
|
||||
/sbin/depmod -a ${KVER}
|
||||
fi
|
||||
|
||||
# check for and remove non-dkms installations
|
||||
# with compressed module in a unique non-standard location (Armbian)
|
||||
# Example: /usr/lib/modules/5.15.80-rockchip64/kernel/drivers/net/wireless/rtl8821cu/8821cu.ko.xz
|
||||
# Dear Armbiam, this is a really bad idea.
|
||||
if [[ -f "/usr/lib/modules/${KVER}/kernel/drivers/net/wireless/${DRV_NAME}/${MODULE_NAME}.ko.xz" ]]
|
||||
then
|
||||
echo "Removing a non-dkms installation: /usr/lib/modules/${KVER}/kernel/drivers/net/wireless/${DRV_NAME}/${MODULE_NAME}.ko.xz"
|
||||
rm -f /usr/lib/modules/${KVER}/kernel/drivers/net/wireless/${DRV_NAME}/${MODULE_NAME}.ko.xz
|
||||
/sbin/depmod -a ${KVER}
|
||||
fi
|
||||
|
||||
# information that helps with bug reports
|
||||
|
||||
# display kernel version
|
||||
echo "Linux Kernel=${KVER}"
|
||||
echo "Kernel: ${KVER}"
|
||||
|
||||
# display architecture
|
||||
echo "CPU Architecture=${KARCH}"
|
||||
echo "Arch: ${KARCH}"
|
||||
|
||||
# determine if dkms is installed and run the appropriate routines
|
||||
if command -v dkms >/dev/null 2>&1
|
||||
@ -94,7 +115,7 @@ then
|
||||
echo "${DRV_NAME}/${DRV_VERSION} has been removed"
|
||||
fi
|
||||
else
|
||||
echo "An error occurred. dkms remove error = ${RESULT}"
|
||||
echo "An error occurred. dkms remove error: ${RESULT}"
|
||||
echo "Please report this error."
|
||||
exit $RESULT
|
||||
fi
|
||||
@ -108,7 +129,7 @@ make clean >/dev/null 2>&1
|
||||
echo "The driver was removed successfully."
|
||||
echo "You may now delete the driver directory if desired."
|
||||
|
||||
# if NoPrompt is not used, ask user some questions to complete removal
|
||||
# if NoPrompt is not used, ask user some questions
|
||||
if [ $NO_PROMPT -ne 1 ]
|
||||
then
|
||||
read -p "Do you want to reboot now? (recommended) [y/N] " -n 1 -r
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user